How to Guides

192.168.0.100 Admin login, Username, Password and IP

An IP Address is an identification of the network you are using. To understand this concept consider this example it just like your home address difference is that instead of where you are living it will give the location of your network. The routers have their IP. 192.168.0.100 IP is assigned to every device you use over a network.

192.168.0.100 Admin login, Username, Password and IP

What is 192.168.0.100 IP Address?

192.168.0.100 is a private IP address. It can only be used on private networks. Private IP address does not need to be unique except within the local networks. The manufacturer of the routers assigns a default IP to their router still 192.168.0.100 is a unique IP address. But still, some of the Broadband models & access points to use it.

Using Administrative console this IP can also be used for configuring your devices. This address is used by Modems, routers or any other devices which are connected to a network. Ser Command US Robotics uses this IP address.

192.168.0.100 IP Admin Login

Log in is quite a simple process. Follow a few steps to login:

Step 1 – Open Web Browser. Then, in search window type 192.168.0.100. Now, you will visit a page where it will ask Username or password once you enter that, your admin page will be open after that you can configure your device.

192.168.0.100 IP Admin Login

Step 2 –  Using this page there are many parameters that you can consider.

Step 3 –  You can experiment with bandwidth and transmission rate also you can monitor devices that are connected to your router.

Step 4 –  You should change the username and password of your device to avoid any security risks.

In some cases, there is no predefined username or password by the manufacturer then you have to configure the system your own.

Also Read:

How to Know your Router’s IP

Step 1 – In the start menu click the search field.

Step 2 – Type cmd there.

Step 3 – A window command prompt will open up.

Step 4 – Enter a command if configure.

Step 5 – List of different addresses. There will be an IP address, Mac address, broadcasting address.

Step 6 – You will find the Router’s IP address under section Local Area Network.

How to Change password

Step 1: Enter your username and password at https://192.168.0.100 by doing this your administrative panel will be opened.

Step 2: Then change your default setting and then apply

What To Do When You Forget Your Username & Password?

This is a complicated procedure so it’s good that you remember your Username & password even if you forget then have a look to it to be on the safer side

Step 1: First of all, turn off the router.

Step 2: Secondly, press & hold the reset button present on the rear panel of the router. You can do this with the help of some pointed things. Now don’t release the reset button and turn on the router. Hold it for 5 to 10 seconds.

Reset Router and IP Address Password and Username

Step 3: Then, release the button & wait for the device to reset.

Step 4: Lastly, using network cable or WiFi connection you have to connect the router to a network.

After doing this you will lose all your preconfigured settings. This will configure your router to the default factory setting.

Important things to keep in mind:

1. Before your router restarts completely you should power it on.

2. Try your default username and password as admin

3. IP address of your computer should be the same as the subnet of your router. Subnet mask should be 255.255.255.0.

Conclusion

Undoubtedly, this is a private network you can access the network when you are a part that network. You have to put a proper IP address. If you use ping command for this 192.168.0.100 IP address, you can’t do it unless you are a part of the network. Furthermore, to use the command you should be the part of the network.

For the best results, you should have a good network connection in your preferred area so that your network works properly. Only by using the admin panel you can configure the devices with the router. For changing any device settings you have to use the same admin panel. So it is really very important to know about the networks that you are using it along with their configuration.

Leave a Reply